1. fdisk

Fdisk is the most commonly used command to check the partitions on a disk. The fdisk command can display the partitions and details like file system type. However it does not report the size of each partitions.

$ sudo fdisk -l

Disk /dev/sda: 500.1 GB, 500107862016 bytes
255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x30093008

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *          63   146801969    73400953+   7  HPFS/NTFS/exFAT
/dev/sda2       146802031   976771071   414984520+   f  W95 Ext'd (LBA)
/dev/sda5       146802033   351614654   102406311    7  HPFS/NTFS/exFAT
/dev/sda6       351614718   556427339   102406311   83  Linux
/dev/sda7       556429312   560427007     1998848   82  Linux swap / Solaris
/dev/sda8       560429056   976771071   208171008   83  Linux

Disk /dev/sdb: 4048 MB, 4048551936 bytes
54 heads, 9 sectors/track, 16270 cylinders, total 7907328 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0001135d

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1   *        2048     7907327     3952640    b  W95 FAT32

Each device is reported separately with details about size, seconds, id and individual partitions.

2. sfdisk

Sfdisk is another utility with a purpose similar to fdisk, but with more features. It can display the size of each partition in MB.

$ sudo sfdisk -l -uM

Disk /dev/sda: 60801 cylinders, 255 heads, 63 sectors/track
Warning: extended partition does not start at a cylinder boundary.
DOS and Linux will interpret the contents differently.
Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0

   Device Boot Start   End    MiB    #blocks   Id  System
/dev/sda1   *     0+ 71680- 71681-  73400953+   7  HPFS/NTFS/exFAT
/dev/sda2     71680+ 476938  405259- 414984520+   f  W95 Ext'd (LBA)
/dev/sda3         0      -      0          0    0  Empty
/dev/sda4         0      -      0          0    0  Empty
/dev/sda5     71680+ 171686- 100007- 102406311    7  HPFS/NTFS/exFAT
/dev/sda6     171686+ 271693- 100007- 102406311   83  Linux
/dev/sda7     271694  273645   1952    1998848   82  Linux swap / Solaris
/dev/sda8     273647  476938  203292  208171008   83  Linux

Disk /dev/sdb: 1020 cylinders, 125 heads, 62 sectors/track
Warning: The partition table looks like it was made
  for C/H/S=*/54/9 (instead of 1020/125/62).
For this listing I'll assume that geometry.
Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0

   Device Boot Start   End    MiB    #blocks   Id  System
/dev/sdb1   *     1   3860   3860    3952640    b  W95 FAT32
                start: (c,h,s) expected (4,11,6) found (0,32,33)
                end: (c,h,s) expected (1023,53,9) found (492,53,9)
/dev/sdb2         0      -      0          0    0  Empty
/dev/sdb3         0      -      0          0    0  Empty
/dev/sdb4         0      -      0          0    0  Empty

3. cfdisk

Cfdisk is a linux partition editor with an interactive user interface based on ncurses. It can be used to list out the existing partitions as well as create or modify them.

Here is an example of how to use cfdisk to list the partitions.

linux cfdisk disk partitions

Cfdisk works with one partition at a time. So if you need to see the details of a particular disk, then pass the device name to cfdisk.

$ sudo cfdisk /dev/sdb

4. parted

Parted is yet another command line utility to list out partitions and modify them if needed.
Here is an example that lists out the partition details.

$ sudo parted -l
Model: ATA ST3500418AS (scsi)
Disk /dev/sda: 500GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number  Start   End     Size    Type      File system     Flags
 1      32.3kB  75.2GB  75.2GB  primary   ntfs            boot
 2      75.2GB  500GB   425GB   extended                  lba
 5      75.2GB  180GB   105GB   logical   ntfs
 6      180GB   285GB   105GB   logical   ext4
 7      285GB   287GB   2047MB  logical   linux-swap(v1)
 8      287GB   500GB   213GB   logical   ext4

Model: Sony Storage Media (scsi)
Disk /dev/sdb: 4049MB
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number  Start   End     Size    Type     File system  Flags
 1      1049kB  4049MB  4048MB  primary  fat32        boot

5. df

Df is not a partitioning utility, but prints out details about only mounted file systems. The list generated by df even includes file systems that are not real disk partitions.

Here is a simple example

$ df -h
Filesystem      Size  Used Avail Use% Mounted on
/dev/sda6        97G   43G   49G  48% /
none            4.0K     0  4.0K   0% /sys/fs/cgroup
udev            3.9G  8.0K  3.9G   1% /dev
tmpfs           799M  1.7M  797M   1% /run
none            5.0M     0  5.0M   0% /run/lock
none            3.9G   12M  3.9G   1% /run/shm
none            100M   20K  100M   1% /run/user
/dev/sda8       196G  154G   33G  83% /media/13f35f59-f023-4d98-b06f-9dfaebefd6c1
/dev/sda5        98G   37G   62G  38% /media/4668484A68483B47

Only the file systems that start with a /dev are actual devices or partitions.
Use grep to filter out real hard disk partitions/file systems.

$ df -h | grep ^/dev
/dev/sda6        97G   43G   49G  48% /
/dev/sda8       196G  154G   33G  83% /media/13f35f59-f023-4d98-b06f-9dfaebefd6c1
/dev/sda5        98G   37G   62G  38% /media/4668484A68483B47

To display only real disk partitions along with partition type, use df like this

$ df -h --output=source,fstype,size,used,avail,pcent,target -x tmpfs -x devtmpfs
Filesystem     Type     Size  Used Avail Use% Mounted on
/dev/sda6      ext4      97G   43G   49G  48% /
/dev/sda8      ext4     196G  154G   33G  83% /media/13f35f59-f023-4d98-b06f-9dfaebefd6c1
/dev/sda5      fuseblk   98G   37G   62G  38% /media/4668484A68483B47

Note that df shows only the mounted file systems or partitions and not all.

6. pydf

Improved version of df, written in python. Prints out all the hard disk partitions in a easy to read manner.

$ pydf
Filesystem Size Used Avail Use%             Mounted on                                 
/dev/sda6   96G  43G   48G 44.7 [####.....] /                                          
/dev/sda8  195G 153G   32G 78.4 [#######..] /media/13f35f59-f023-4d98-b06f-9dfaebefd6c1
/dev/sda5   98G  36G   61G 37.1 [###......] /media/4668484A68483B47

Again, pydf is limited to showing only the mounted file systems.

7. lsblk

Lists out all the storage blocks, which includes disk partitions and optical drives. Details include the total size of the partition/block and the mount point if any.
Does not report the used/free disk space on the partitions.

$ lsblk
sda      8:0    0 465.8G  0 disk 
├─sda1   8:1    0    70G  0 part 
├─sda2   8:2    0     1K  0 part 
├─sda5   8:5    0  97.7G  0 part /media/4668484A68483B47
├─sda6   8:6    0  97.7G  0 part /
├─sda7   8:7    0   1.9G  0 part [SWAP]
└─sda8   8:8    0 198.5G  0 part /media/13f35f59-f023-4d98-b06f-9dfaebefd6c1
sdb      8:16   1   3.8G  0 disk 
└─sdb1   8:17   1   3.8G  0 part 
sr0     11:0    1  1024M  0 rom

If there is no MOUNTPOINT, then it means that the file system is not yet mounted. For cd/dvd this means that there is no disk.

Lsblk is capbale of displaying more information about each device like the label and model. Check out the man page for more information

8. blkid

Prints the block device (partitions and storage media) attributes like uuid and file system type. Does not report the space on the partitions.

$ sudo blkid
/dev/sda1: UUID="5E38BE8B38BE6227" TYPE="ntfs" 
/dev/sda5: UUID="4668484A68483B47" TYPE="ntfs" 
/dev/sda6: UUID="6fa5a72a-ba26-4588-a103-74bb6b33a763" TYPE="ext4" 
/dev/sda7: UUID="94443023-34a1-4428-8f65-2fb02e571dae" TYPE="swap" 
/dev/sda8: UUID="13f35f59-f023-4d98-b06f-9dfaebefd6c1" TYPE="ext4" 
/dev/sdb1: UUID="08D1-8024" TYPE="vfat"

9. hwinfo

The hwinfo is a general purpose hardware information tool and can be used to print out the disk and partition list. The output however does not print details about each partition like the above commands.

$ hwinfo --block --short
  /dev/sda             ST3500418AS
  /dev/sdb             Sony Storage Media
  /dev/sda1            Partition
  /dev/sda2            Partition
  /dev/sda5            Partition
  /dev/sda6            Partition
  /dev/sda7            Partition
  /dev/sda8            Partition
  /dev/sdb1            Partition
  /dev/sr0             SONY DVD RW DRU-190A


The output of parted is concise and complete to get an overview of different partitions, file system on them and the total space. Pydf and df are limited to showing only mounted file systems and the same on them.

Fdisk and Sfdisk show a whole lot of information that can take sometime to interpret whereas, Cfdisk is an interactive partitioning tool that display a single device at a time.

So try them out, and do not forget to comment below.

  • Inaugural Bitcoin Fair in San Francisco Sees High Turnout
  • Sberbank Buys Commercial Bonds Issued Over Blockchain Platform
  • Bitcoin Drops Below $4,000 as Market Turns Uncertain
  • Coinbase Now Allows Merchants to Offer 25% Discounts on Bitcoin Purchases
  • Overstock’s tZERO Wins Patent for Integrating Crypto With Legacy Trading Tech
  • Linux / Unix – crontab: no crontab for user using an empty one error and solution
  • Use wget Command To Download Files From HTTPS Domains
  • CryptoKitties Charity Auction Raises $15K for Children’s Hospital
  • Bitcoin Micropayments Get Big Moment as Chicago Sun-Times Paywall Experiment Goes Live
  • Safello Launches Free Bitcoin Fundraising Service for Charities
  • Taiwan Central Bank Chief Cautious on Central Bank Crypto
  • Bitstamp Suffers Banking Software Issue and Site Downtime
  • Digital Advocacy Groups Critical of California Bitcoin Regulation
  • Cisco: Bitcoin Phishing Scam Bagged $50 Million Over 3 Years
  • Ethereum’s Next Blockchain Upgrade Faces Delay After Testing Failure
  • SXI LLC Company
    SXI.IO is a global Blockchain software company, specialized in developing white label crypto exchange platforms , Wallet platforms, ICO platforms, Token Erc20 .....
    Fully Managed VPS Fully Managed VPS Fully Managed VPS

    You Might Also Enjoy NewS Post