Linux Create Software RAID 1 (Mirror) Array

How do I create Software RAID 1 arrays on Linux systems without using GUI tools or installer options? How do I setup RAID 1 array under Linux systems?

You need to install mdadm which is used to create, manage, and monitor Linux software MD (RAID) devices. RAID devices are virtual devices created from two or more real block devices. This allows multiple devices (typically disk drives or partitions) to be combined into a single device to hold (for example) a single filesystem. Some RAID levels include redundancy and can survive some degree of device failure.

Linux Support For Software RAID

Currently, Linux supports the following RAID levels (quoting from the man page):

  2. RAID0 (striping)
  3. RAID1 (mirroring)
  4. RAID4
  5. RAID5
  6. RAID6
  7. RAID10

MULTIPATH is not a Software RAID mechanism, but does involve multiple devices: each device is a path to one common physical storage device. FAULTY is also not true RAID, and it only involves one device. It provides a layer over a true device that can be used to inject faults.

Install mdadm

Type the following command under RHEL / CentOS / Fedora Linux:
# yum install mdadm
Type the following command under Debian / Ubuntu Linux:
# apt-get update && apt-get install mdadm

How Do I Create RAID1 Using mdadm?

Type the following command to create RAID1 using /dev/sdc1 and /dev/sdd1 (20GB size each). First run fdisk on /dev/sdc and /dev/sdd with “Software Raid” type i.e. type 0xfd:
# fdisk /dev/sdc
# fdisk /dev/sdd

See fdisk(8) man page to setup partition type. Do not format partition. Just create the same. Now, create RAID-1 as follows.

If the device contains a valid md superblock, the block is overwritten with zeros:

# mdadm --zero-superblock /dev/sdc /dev/sdd

Create RAID1 using /dev/sdc1 and /dev/sdd1

# mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sdc1 /dev/sdd1

Format /dev/md0 as ext3:

# mkfs.ext3 /dev/md0

Mount /dev/md0

# mkdir /raid1
# mount /dev/md0 /raid1
# df -H

Edit /etc/fstab

Make sure RAID1 get mounted automatically. Edit /etc/fstab and append the following line:

/dev/md0 /raid1 ext3 noatime,rw 0 0

Save and close the file.

How Do I See RAID Array Building Progress and Current Status?

Type the following command:
# watch -n 2 cat /proc/mdstat
# tail -f /proc/mdstat

Update /etc/mdadm.conf File

Update or edit /etc/mdadm/mdadm.conf or /etc/mdadm.conf (distro specific location) file as follows:

ARRAY /dev/md0 devices=/dev/sdc1,/dev/sdd1 level=1 num-devices=2 auto=yes

This config file lists which devices may be scanned to see if they contain MD super block, and gives identifying information (e.g. UUID) about known MD arrays. Please note that Linux kernel v2.6.xx above can use both /dev/mdX or /dev/md/XX names. You can also create partitions for /dev/md/XX as /dev/md/d1/p2.

How Do I Get Information On Existing Array?

Type the following command
# mdadm --query /dev/md0
This will find out if a given device is a raid array, or is part of one, and will provide brief information about the device.


  • See man pages: mdadm(8) and mdadm.conf(5)
  • RAID 5 vs RAID 10: Recommended RAID For Safety and Performance

Posted by: SXI ADMIN

The author is the creator of SXI LLC and a seasoned sysadmin, DevOps engineer, and a trainer for the Linux operating system/Unix shell scripting. Get the latest tutorials on SysAdmin, Linux/Unix and open source topics via RSS/XML feed or weekly email newsletter.